Ergebnis 1 bis 1 von 1
  1. #1
    Senior Mitglied
    Registriert seit
    30.11.2013
    Beiträge
    141
    Thanks (gegeben)
    25
    Thanks (bekommen)
    5
    Total Downloaded
    4,84 MB
    Total Downloaded
    4,84 MB
    ReceiverDanke

    Serielle Schnittstelle RS232 am ET6500

    Hi,

    ich hab mir das Board mal angesehen und eine Serielle Schnittstelle gefunden.
    Ich musste das Signal invertieren um sinnvolle Daten zu bekommen, das kann jetzt aber auch an meinen Setup gelegen haben.

    Parameter:

    Bit rate 115200
    Data 8 bits
    Stop 1 bit
    no parity

    (also 8N1 115200)

    Anbei ein Bild mit den Pins, der Ausschnitt ist direkt neben dem Tuner (weiß Tx, schwarz GND).
    Serielle Schnittstelle RS232 am ET6500-et6500_serial_anno.jpg

    Hier noch der Bootvorgang:
    Code:
    BCM74130011012
    K1
    K2
    
    
    K3
    
    
    K4
    
    
    K5
    
    
    Shmoo Version=3.8
    DDR Freq=0x0000018C
    %00000001%
    RC1=00000006
    WC1=FFFFFFF0
    RC2=0000001F
    WC2=00000034
    RC3=00000012
    WC3=FFFFFFE9
    RC4=00000012
    WC4=00000035
    NWC=0000000F
    RC5=00000007
    WC5=0000000F
    RC6=0000001F
    WC6=0000000F
    NRC=00000013
    RW=00000019
    WW=0000004D
    G=00000000 R=00000013 W=0000000F 
    BL=00000000
    RC1=00000004
    RC2=00000019
    
    
    BL=00000001
    RC1=00000008
    RC2=0000001F
    
    
    BL=00000002
    RC1=00000006
    RC2=00000018
    
    
    BL=00000003
    RC1=00000007
    RC2=00000019
    
    
    BL=00000004
    RC1=00000006
    RC2=0000001A
    
    
    BL=00000005
    RC1=00000009
    RC2=0000001F
    
    
    BL=00000006
    RC1=00000003
    RC2=00000018
    
    
    BL=00000007
    RC1=00000005
    RC2=0000001A
    SCfC3
    COPY CODE
    COMPARE CODE
    4567
    
    
    BCM97413B1 CFE v2.26COMMA CFE core v2.12COMMA Endian Mode: Little
    Build Date: Sat Feb  4 17:55:31 WEST 2012 (Administrator@buildserver)
    Copyright (C) Broadcom Corporation.
    
    
    start cfe init device
    sec-0 nblks=8 blksiz=8192
    sec-1 nblks=63 blksiz=65536
    Enabling NAND flash at CS1COMMA NOR flash at CS0
    NAND Flash size = 1024MB
    CPU speed:     405MHz
    Memory Config: 64-bit UMA
    Device Tech:   1Gb
    Total memory:  512MB
    Boot Device:   NOR
    Total flash:   4MB
    
    
    Initializing USB.
    USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
    USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
    
    
    CFE initialized.
    Set default GPIO...
    USB: New device connected to bus 1 hub 1 port 1'27'[J
    USB: Resetting device on bus 1 port 1'27'[J
    USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
    USB: New device connected to bus 1 hub 2 port 2'27'[J
    USB: Resetting device on bus 1 port 2'27'[J
    USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
    USB: [Transfer error: 4]
    USB CDC Device  (00:00:00:00:00:00)
    Starting splash screen.
    ***************************************************
    Found splash image - Width = 720 Height = 576
    bmp ptr : 0x8fa00000 COMMA surface ptr : 0xafc00000
    ***************************************************
    
    
    Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
    Loading: 0x80001000/8157312 0x807c8880/139408 Entry address is 0x80600fd0
    TP1 Entry Address at 0x80000ffc = 80600fd0
    Starting program at 0x80600fd0
    
    
    Linux version 3.8.7 (oe1@BUILD2) (gcc version 4.9.2 (GCC) ) #1 SMP Wed Nov 11 21:10:59 CET 2015
    Fetching vars from bootloader... found 10 vars.
    Options: enet_en=1 enet0_mii=0 enet_no_mdio=0 enet1_en=1 moca=0
             sata=1 docsis=0 pci=1 pcie=0 smp=1 usb=1
    Using 512 MB + 0 MB RAM (from CFE)
    CPU revision is: 0002a044 (Brcm4380)
    FPU revision is: 00130001
    Determined physical RAM map:
     memory: 10000000 @ 00000000 (usable)
     memory: 10000000 @ 20000000 (usable)
    bmem: adding 216 MB RESERVED region at 40 MB (0x0d800000@0x02800000)
    Zone ranges:
      Normal   [mem 0x00000000-0x2fffffff]
    Movable zone start for each node
    Early memory node ranges
      node   0: [mem 0x00000000-0x0fffffff]
      node   0: [mem 0x20000000-0x2fffffff]
    Primary instruction cache 32kBCOMMA VIPTCOMMA 2-wayCOMMA linesize 64 bytes.
    Primary data cache 64kBCOMMA 4-wayCOMMA VIPTCOMMA cache aliasesCOMMA linesize 64 bytes
    PERCPU: Embedded 7 pages/cpu @81407000 s6272 r8192 d14208 u32768
    Built 1 zonelists in Zone orderCOMMA mobility grouping on.  Total pages: 130048
    Kernel command line:  bmem=216M ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs console=ttyS0COMMA115200n8
    PID hash table entries: 2048 (order: 1COMMA 8192 bytes)
    Dentry cache hash table entries: 65536 (order: 6COMMA 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5COMMA 131072 bytes)
    __ex_table already sortedCOMMA skipping sort
    Memory: 290412k/524288k available (6181k kernel codeCOMMA 233876k reservedCOMMA 1538k dataCOMMA 276k initCOMMA 0k highmem)
    Hierarchical RCU implementation.
    NR_IRQS:160
    Detected MIPS clock frequency: 405 MHz (202.500 MHz counter)
    Console: colour dummy device 80x25
    Calibrating delay loop... 401.40 BogoMIPS (lpj=200704)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 512
    SMP: Booting CPU1...
    CPU revision is: 0002a044 (Brcm4380)
    FPU revision is: 00130001
    Primary instruction cache 32kBCOMMA VIPTCOMMA 2-wayCOMMA linesize 64 bytes.
    Primary data cache 64kBCOMMA 4-wayCOMMA VIPTCOMMA cache aliasesCOMMA linesize 64 bytes
    SMP: CPU1 is running
    Brought up 2 CPUs
    devtmpfs: initialized
    NET: Registered protocol family 16
    USB0: power enable is active low; overcurrent is active low
    PCI2.3->SDRAM window: 512 MB
    bio: create slab <bio-0> at 0
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Linux video capture interface: v2.00
    Advanced Linux Sound Architecture Driver Initialized.
    PCI host bridge to bus 0000:00
    pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
    pci_bus 0000:00: root bus resource [io  0x0400-0x83ff]
    pci_bus 0000:00: No busn resource found for root busCOMMA will use [bus 00-ff]
    PCI host bridge to bus 0000:01
    pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
    pci_bus 0000:01: root bus resource [io  0x8400-0x87ff]
    pci_bus 0000:01: No busn resource found for root busCOMMA will use [bus 01-ff]
    PCI: found device 14e4:8602 on SATA busCOMMA slot 0 (irq 42)
    pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
    pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
    Bluetooth: Core ver 2.16
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: SCO socket layer initialized
    cfg80211: Calling CRDA to update world regulatory domain
    Switching to clocksource upg
    FS-Cache: Loaded
    NET: Registered protocol family 2
    TCP established hash table entries: 4096 (order: 3COMMA 32768 bytes)
    TCP bind hash table entries: 4096 (order: 3COMMA 32768 bytes)
    TCP: Hash tables configured (established 4096 bind 4096)
    TCP: reno registered
    UDP hash table entries: 256 (order: 1COMMA 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1COMMA 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    NFS: Registering the id_resolver key type
    Key type id_resolver registered
    Key type id_legacy registered
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    fuse init (API version 7.20)
    msgmni has been set to 567
    io scheduler noop registered
    io scheduler cfq registered (default)
    Serial: 8250/16550 driverCOMMA 4 portsCOMMA IRQ sharing disabled
    serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
    console [ttyS0] enabled
    serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
    serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
    loop: module loaded
    PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
    scsi0 : sata_brcmstb
    scsi1 : sata_brcmstb
    ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
    ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
    Broadcom STB NAND controller (BrcmNand Controller)
    bcmemac: Broadcom STB 10/100 EMAC driver v3.0
    bcmemac: registered interface #0 at 0x10080000 as 'eth0 '(00:16:b4:05:a8:35)
    bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
    usbcore: registered new interface driver zd1201
    ehci_hcd: USB 2.0 'Enhanced 'Host Controller (EHCI) Driver
    ehci-brcm ehci-brcm.0: Broadcom STB EHCI
    ehci-brcm ehci-brcm.0: new USB bus registeredCOMMA assigned bus number 1
    ehci-brcm ehci-brcm.0: irq 62COMMA io mem 0x10480300
    ehci-brcm ehci-brcm.0: USB 0.0 startedCOMMA EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ehci-brcm ehci-brcm.1: Broadcom STB EHCI
    ehci-brcm ehci-brcm.1: new USB bus registeredCOMMA assigned bus number 2
    ehci-brcm ehci-brcm.1: irq 57COMMA io mem 0x10480500
    ehci-brcm ehci-brcm.1: USB 0.0 startedCOMMA EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ohci_hcd: USB 1.1 'Open 'Host Controller (OHCI) Driver
    ohci-brcm ohci-brcm.0: Broadcom STB OHCI
    ohci-brcm ohci-brcm.0: new USB bus registeredCOMMA assigned bus number 3
    ohci-brcm ohci-brcm.0: irq 63COMMA io mem 0x10480400
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ohci-brcm ohci-brcm.1: Broadcom STB OHCI
    ohci-brcm ohci-brcm.1: new USB bus registeredCOMMA assigned bus number 4
    ohci-brcm ohci-brcm.1: irq 64COMMA io mem 0x10480600
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    usbcore: registered new interface driver btusb
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    TCP: cubic registered
    NET: Registered protocol family 17
    Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    ata1: SATA link down (SStatus 4 SControl 300)
    Bluetooth: HIDP socket layer initialized
    Key type dns_resolver registered
    EBI CS1: setting up NAND flash (primary)
    mtd->oobsize=0COMMA mtd->eccOobSize=0
    NAND_CS_NAND_XOR=00000000
    B4: NandSelect=50000200COMMA nandConfig=18152300COMMA chipSelect=1
    brcmnand_read_id: CS1: dev_id=ecd35195
    After: NandSelect=50000200COMMA nandConfig=18152300
    Block size=00020000COMMA erase shift=17
    NAND Config: Reg=18152300COMMA chipSize=1024 MBCOMMA blockSize=128KCOMMA erase_shift=11
    busWidth=1COMMA pageSize=2048BCOMMA page_shift=11COMMA page_mask=000007ff
    timing1 not adjusted: 5363444f
    timing2 not adjusted: 00000fc6
    eccLevel=15COMMA 1Ksector=0COMMA oob=16
    nbrBitsPerCell=2COMMA cellinfo=0COMMA chip->cellinfo=00000000
    <--brcmnand_set_acccontrol: acc b4: d7ff1010COMMA after: d7ff1010
    BrcmNAND mfg ec d3 Samsung K9F8G08U0M 1024MB on CS1
    
    
    Found NAND on CS1: ACC=d7ff1010COMMA cfg=18152300COMMA flashId=ecd35195COMMA tim1=5363444fCOMMA tim2=00000fc6
    BrcmNAND version = 0x0302 1024MB @00000000
    B4: NandSelect=50000200COMMA nandConfig=18152300COMMA chipSelect=1
    brcmnand_read_id: CS1: dev_id=ecd35195
    After: NandSelect=50000200COMMA nandConfig=18152300
    Found NAND flash on Chip Select 1COMMA chipSize=1024MBCOMMA usable size=1024MBCOMMA base=0
    brcmnand_scan: B4 nand_select = 50000200
    brcmnand_scan: After nand_select = 50000200
    page_shift=11COMMA bbt_erase_shift=17COMMA chip_shift=30COMMA phys_erase_shift=17
    Brcm NAND controller version = 3.2 NAND flash size 1024MB @00000000
    ECC layout=brcmnand_oob_bch4_4k
    usb 2-1: new high-speed USB device number 2 using ehci-brcm
    brcmnand_scan:  mtd->oobsize=64
    brcmnand_scan: oobavail=50COMMA eccsize=512COMMA writesize=2048
    brcmnand_scanCOMMA eccsize=512COMMA writesize=2048COMMA eccsteps=4COMMA ecclevel=15COMMA eccbytes=3
    -->brcmnand_default_bbt
    brcmnand_default_bbt: bbt_td = bbt_main_descr
    Adjust partition complete size from entire device to 3ff80000 to avoid overlap with BBT reserved space
    Adjust partition rootfs size from entire device to 3f980000 to avoid overlap with BBT reserved space
    Creating 3 MTD partitions on "brcmnand.0":
    0x000000000000-0x00003ff80000 : "complete"
    0x000000000000-0x000000600000 : "kernel"
    0x000000600000-0x00003ff80000 : "rootfs"
    PM: CP0 COUNT/COMPARE frequency depends on divisor
    UBI: attaching mtd2 to ubi0
    hub 2-1:1.0: USB hub found
    hub 2-1:1.0: 4 ports detected
    ata2: SATA link down (SStatus 4 SControl 300)
    usb 2-1.2: new full-speed USB device number 3 using ehci-brcm
    UBI: scanning is finished
    UBI: attached mtd2 (name "rootfs"COMMA size 1017 MiB) to ubi0
    UBI: PEB size: 131072 bytes (128 KiB)COMMA LEB size: 126976 bytes
    UBI: min./max. I/O unit sizes: 2048/2048COMMA sub-page size 2048
    UBI: VID header offset: 2048 (aligned 2048)COMMA data offset: 4096
    UBI: good PEBs: 8138COMMA bad PEBs: 2COMMA corrupted PEBs: 0
    UBI: user volume: 1COMMA internal volumes: 1COMMA max. volumes count: 128
    UBI: max/mean erase counter: 2/0COMMA WL threshold: 4096COMMA image sequence number: 640242473
    UBI: available PEBs: 0COMMA total reserved PEBs: 8138COMMA PEBs reserved for bad PEB handling: 158
    ALSA device list:
      No soundcards found.
    UBI: background thread "ubi_bgt0d" startedCOMMA PID 48
    UBIFS: background thread "ubifs_bgt0_0" startedCOMMA PID 49
    UBIFS: recovery needed
    UBIFS: recovery completed
    UBIFS: mounted UBI device 0COMMA volume 0COMMA name "rootfs"(null)
    UBIFS: LEB size: 126976 bytes (124 KiB)COMMA min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS: FS size: 518696960 bytes (494 MiBCOMMA 4085 LEBs)COMMA journal size 9023488 bytes (8 MiBCOMMA 72 LEBs)
    UBIFS: reserved for root: 0 bytes (0 KiB)
    UBIFS: media format: w4/r0 (latest is w4/r0)COMMA UUID 926E6218-013D-4494-B473-6E2C9CA867B9COMMA small LPT model
    VFS: Mounted root (ubifs filesystem) on device 0:10.
    devtmpfs: mounted
    Freeing unused kernel memory: 276k freed
    INIT: version 2.88 booting
    usbcore: registered new interface driver tpm
    dvb: module_layout: kernel tainted.
    Disabling lock debugging due to kernel taint
    input: dreambox remote control (native) as /devices/virtual/input/input0
    input: dreambox advanced remote control (native) as /devices/virtual/input/input1
    DVB: registering new adapter (dvb0)
    platform dvb0.0: DVB: registering adapter 0 frontend 0 (DVB-S2)...
    input: front panel as /devices/virtual/input/input2
    SGI XFS with security attributesCOMMA realtimeCOMMA large block/inode numbersCOMMA no debug enabled
    ALSA: Restoring mixer settings...
    net.ipv4.conf.default.rp_filter = 1
    net.ipv4.conf.all.rp_filter = 1
    vm.dirty_writeback_centisecs = 300
    vm.dirty_background_ratio = 1
    vm.min_free_kbytes = 8192
    vm.dirty_ratio = 60
    vm.swappiness = 30
    INIT: Entering runlevel: 3
    Configuring network interfaces... wpa_supplicant v2.4
    random: Trying to read entropy from /dev/random
    Successfully initialized wpa_supplicant
    Initializing interface 'wlan0 'conf '/etc/wpa_supplicant.wlan0.conf 'driver 'wext 'ctrl_interface 'N/A 'bridge 'N/A'
    Configuration file '/etc/wpa_supplicant.wlan0.conf '-> '/etc/wpa_supplicant.wlan0.conf'
    Reading configuration file '/etc/wpa_supplicant.wlan0.conf'
    ctrl_interface='/var/run/wpa_supplicant'
    eapol_version=1
    fast_reauth=1
    ap_scan=1
    Line: 6 - start of a new network block
    ssid - hexdump_ascii(len=11):
         6c 65 2d 73 74 65 72 6e 2d 6d 65                  *SSID*(edited)     
    scan_ssid=0 (0x0)
    key_mgmt: 0x2
    proto: 0x2
    pairwise: 0x10
    group: 0x10
    PSK (ASCII passphrase) - hexdump_ascii(len=15): [REMOVED]
    PSK (from passphrase) - hexdump(len=32): [REMOVED]
    Priority group 0
       id=0 ssid='le-stern-me'
    Could not read interface wlan0 flags: No such device
    WEXT: Could not set interface 'wlan0 'UP
    wlan0: Failed to initialize driver interface
    Failed to add interface wlan0
    wlan0: Cancelling scan request
    wlan0: Cancelling authentication timeout
    ip: SIOCGIFFLAGS: No such device
    Starting system message bus: dbus.
    Starting Dropbear SSH server: NET: Registered protocol family 10
    dropbear.
    Starting automount: automount: program is already running.
    done.
    Starting rpcbind daemon...done.
    starting 8 nfsd kernel threads: done
    starting mountd: done
    Mounting remote filesystems...
    creating NFS state directory: done
    starting statd: done
    starting Busybox Periodic Command Scheduler: crond... done.
    crond[399]: crond (busybox 1.23.2) startedCOMMA log level 8
    
    
    Starting internet superserver: inetd.
    Starting Samba: smbd nmbd.
    Starting syslogd/klogd: done
    Starting telnet server: telnetd.
    * starting FTP Server: vsftpd... done.
     * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
       ...done.
    net.ipv4.conf.default.rp_filter = 1
    net.ipv4.conf.all.rp_filter = 1
    vm.dirty_writeback_centisecs = 300
    vm.dirty_background_ratio = 1
    vm.min_free_kbytes = 8192
    vm.dirty_ratio = 60
    vm.swappiness = 30
    PYTHONPATH: /usr/lib/enigma2/python
    DVB_API_VERSION 5 DVB_API_VERSION_MINOR 9
    enigma2 is the main pvr application... adjust oom score!
    framebuffer not available.
    executing main
    Geändert von DocSnyd3r (08.01.2017 um 20:33 Uhr)

  2. Thanks Berber bedankten sich
    •   Alt Advertising

       


Stichworte

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
Alle Zeitangaben in WEZ +1. Es ist jetzt 09:06 Uhr.
Powered by vBulletin® Version 4.2.5 (Deutsch)
Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.
Resources saved on this page: MySQL 5,26%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
vBulletin Skin By: PurevB.com