Thanks: 0
Ergebnis 1 bis 8 von 8
-
15.03.2019, 20:47 #1
- Registriert seit
- 21.04.2017
- Ort
- Brmen
- Beiträge
- 15
- Thanks (gegeben)
- 1
- Thanks (bekommen)
- 0
- Total Downloaded
- 635,3 KB
- Total Downloaded
- 635,3 KB
Box 1:Xtrend Et 10000Box 2:Xtrend ET 9500Xtrend ET 4000 Open Atv Flashen
Hallo Leute es wäre zu schön wenn es auf einmal klappen würde . Ich habe hier eine Xtrened 4000 mit Pli Software.
Ich habe mir eine Open Atv 6.2 herunter geladen.
Leider weiß ich nicht welchen Knopf ich bei dem Flesh Vorgang Drücken muss, und wann. In Foren steht das ich die OK Taste Drücken muss in anderen soll ich die CH Taste drücken.
Beides hat bis Jetzt nicht geklappt. Ich habe auch mit 4 unterschiedlichsten USB stick probier. Leider Erfolgs los.
Kann mir jemand genau sagen wie ich vorgehen soll ich kann mir nicht vorstellen das keiner von den Sticks funktionier . meine ET 10000 habe ich mit den Sticks schließlich ebenfalls geflescht
Thanks All!!
-
Advertising
-
15.03.2019, 20:59 #2
- Registriert seit
- 23.04.2013
- Beiträge
- 323
- Thanks (gegeben)
- 15
- Thanks (bekommen)
- 53
- Total Downloaded
- 18,07 MB
- Total Downloaded
- 18,07 MB
Box 1:Mut@nt HD51Hallo,
hast du mal versucht die Datei noforce in force umzubenennen?
Dann sollte sie automatisch flashen.
Stick vorne und hinten probiert?------------------------------
-- Es ist wie es ist --
-
15.03.2019, 21:10 #3
- Registriert seit
- 23.04.2013
- Beiträge
- 323
- Thanks (gegeben)
- 15
- Thanks (bekommen)
- 53
- Total Downloaded
- 18,07 MB
- Total Downloaded
- 18,07 MB
Box 1:Mut@nt HD51eine Englische Anleitung kann ich dir zeigen (es ist nicht die OK Taste) :
Flashing the Receiver.
–Fully power the receiver down via the rocker switch at the rear of the receiver.
–Make sure no USB devices are plugged into the receiver at this point.
–Insert the USB stick containing the image files into one of the USB ports on the receiver.
–Power the receiver on from the rear rocker switch.
–You should see the orange and yellow LED's light up to signify that the receiver has detected a viable update on the USB stick.
–If you see the above LED's light up, press the Top button located under the card flap on the front of the receiver
to initiate the flashing process, at this point the Green LED should also light up to confirm the receiver is being flashed.
–If successful the orange and yellow LED's will go out and the receiver will reboot it self.
The flashing process should take approximately two to four minutes to complete, while the receiver is being flashed it is
vitally important that you DO NOT power the receiver down for any reason as this can cause serious and or permanent damage.
If you do not see the orange and yellow LED's light up when you reboot the receiver you may need to check that the file
structure is correct on the USB stick or try formatting the USB stick ( try a different one ).
Please note.
you will always see the orange and yellow LED's light up if the receiver has detected a viable imageto flash on the
inserted media at bootup, It is perfectly safe and advisable to keep a image on your USB stick for backup reasons.
The image will only be flashed to the receiver if you press the Top button when you see these LED's light up,
if you dont press UP button the receiver will boot as normal.------------------------------
-- Es ist wie es ist --
-
15.03.2019, 22:07 #4
- Registriert seit
- 21.04.2017
- Ort
- Brmen
- Beiträge
- 15
- Thanks (gegeben)
- 1
- Thanks (bekommen)
- 0
- Total Downloaded
- 635,3 KB
- Total Downloaded
- 635,3 KB
ThemenstarterBox 1:Xtrend Et 10000Box 2:Xtrend ET 9500das muss ich aber nur bei der PLI Software machen oder ?
Bei der Open ATV Image muss ich es ebenfalls umbenennen??
dacht nur die PLI Images
-
15.03.2019, 22:09 #5
- Registriert seit
- 21.04.2017
- Ort
- Brmen
- Beiträge
- 15
- Thanks (gegeben)
- 1
- Thanks (bekommen)
- 0
- Total Downloaded
- 635,3 KB
- Total Downloaded
- 635,3 KB
ThemenstarterBox 1:Xtrend Et 10000Box 2:Xtrend ET 9500Wenn die Englsche auch die richtige ist .. es gibt so viele die für alle Xtrend s geschrieben wurden . Die 9 und 1000er serie wir etwas anders vorgegangen, danke .
-
15.03.2019, 22:16 #6
- Registriert seit
- 21.04.2017
- Ort
- Brmen
- Beiträge
- 15
- Thanks (gegeben)
- 1
- Thanks (bekommen)
- 0
- Total Downloaded
- 635,3 KB
- Total Downloaded
- 635,3 KB
ThemenstarterBox 1:Xtrend Et 10000Box 2:Xtrend ET 9500Danke Klöön ich habe erst jetzt gesehen das der Xtrend CT 4000 , wenn ich die Klappe öffne 2 schwarze tasten hat , die obere taste soll laut der Beschreibung gedrückt werden . Danke das werde ich gleich morgen ausprobieren . Top endlich eine aussagekräftige Hilfestellung. Top. Muss nur noch Morgen laufen
-
15.03.2019, 22:17 #7
- Registriert seit
- 23.04.2013
- Beiträge
- 323
- Thanks (gegeben)
- 15
- Thanks (bekommen)
- 53
- Total Downloaded
- 18,07 MB
- Total Downloaded
- 18,07 MB
Box 1:Mut@nt HD51Ich glaube schon das die richtig ist denn an eine OK Taste kann ich mich nicht erinnern (ist aber auch schon 1 Jahr her).
Das mit force geht meine ich bei allen Images.------------------------------
-- Es ist wie es ist --
-
24.04.2019, 18:39 #8
- Registriert seit
- 21.12.2014
- Beiträge
- 167
- Thanks (gegeben)
- 7
- Thanks (bekommen)
- 3
- Total Downloaded
- 999,7 KB
- Total Downloaded
- 999,7 KB
erfolg?.....
Lesezeichen