Thanks Thanks:  0
Ergebnis 1 bis 5 von 5
  1. #1
    Mitglied
    Registriert seit
    12.11.2016
    Ort
    Rheinland-Pfalz
    Beiträge
    44
    Total Downloaded
    65,57 MB
    Total Downloaded
    65,57 MB
    ReceiverDankeAktivitäten
    Box 1:
    Octagon SF3038 Triple
     
     
    Box 2:
    Red Eagle Singlebox
     
     
    Box 3:
    Edision Nino
     
     
    Box 4:
    Medialink Ixxus Zero
     
     
    Box 5:
    Medialink Ixxus One
     
     

    Nach flash geht nix mehr

    Nach dem flashen meines Ixuss Zero geht nichts mehr. Er schreibt im Display nur noch "ixusszero", nimmt mein USB-Stick nicht mehr an und reagiert auch nicht auf die Fernbedienung.
    Bei meinem anderen Zero wird der Stick direkt erkannt und er schreibt mir "if you want ...". Ich habe bereits 4 USB-Stick versucht, auch neu formatiert auf FAT und FAT32, mehrere Image runtergeladen und auf Stick kopiert, dabei auch die Reihenfolge vom Pfad beachtet, aber es passiert nichts mehr. Wenn ich den Schalter an der Box auf an stelle, sehe ich das der Stick blinkt aber mehr auch nicht. Auf dem TV sehe ich nur das Bootlogo. Was kann ich noch tun, bevor ich ganz verzweifele?

    •   Alt Advertising

       

  2. #2
    Anfänger
    Registriert seit
    23.12.2013
    Beiträge
    12
    Total Downloaded
    2,50 MB
    Total Downloaded
    2,50 MB
    ReceiverDankeAktivitäten
    Habe aktuelles Image 6.3 Installiert inkl. Bootloaderupdate:

    Code:
    flashdrv_write2 end res 0
    done
    NAND Flash size = 128MB
    DDR Freq:      396MHz
    CPU speed:     405MHz
    Memory Config: 64-bit UMA
    Device Tech:   1Gb
    Total memory:  512MB
    Boot Device:   NOR
    Total flash:   4MB
    Starting splash screen.
    ***************************************************
    Found splash image - Width = 720 Height = 576
    ***************************************************
    
    Failed: Device not found
    flash0: Device not found
    ## ixusszero-1.0.2 : openatv-6.3-ixus ##
    Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:rootfstype=jffs2 root=/dev/mtdblock0 rw mem=128M
    Loading: 0x80001000/7537184 0x80731220/118192 Entry address is 0x8059aaa0
    TP1 Entry Address at 0x80000ffc = 8059aaa0
    Starting program at 0x8059aaa0
    
    Linux version 3.3.0 (oe-user@oe-host) (gcc version 8.2.0 (GCC) ) #1 SMP Wed May 1 18:59:40 UTC 2019
    Fetching vars from bootloader... found 9 vars.
    Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
    Using 512 MB + 0 MB RAM (from CFE)
    CPU revision is: 0002a044 (Brcm4380)
    FPU revision is: 00130001
    Determined physical RAM map:
     memory: 10000000 @ 00000000 (usable)
     memory: 10000000 @ 20000000 (usable)
    bmem: adding 216 MB RESERVED region at 40 MB (0x0d800000@0x02800000)
    Zone PFN ranges:
      Normal   0x00000000 -> 0x00030000
    Movable zone start PFN for each node
    Early memory PFN ranges
        0: 0x00000000 -> 0x00010000
        0: 0x00020000 -> 0x00030000
    PERCPU: Embedded 7 pages/cpu @81407000 s4640 r8192 d15840 u32768
    Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 129536
    Kernel command line: bmem=216M ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200n8
    PID hash table entries: 2048 (order: 1, 8192 bytes)
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    Memory: 291040k/524288k available (5822k kernel code, 233248k reserved, 1294k data, 244k init, 0k highmem)
    Hierarchical RCU implementation.
    NR_IRQS:128
    Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
    Console: colour dummy device 80x25
    Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 512
    SMP: Booting CPU1...
    CPU revision is: 0002a044 (Brcm4380)
    FPU revision is: 00130001
    Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
    Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
    SMP: CPU1 is running
    Brought up 2 CPUs
    devtmpfs: initialized
    NET: Registered protocol family 16
    PCI2.3->SDRAM window: 512 MB
    bio: create slab <bio-0> at 0
    SCSI subsystem initialized
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Advanced Linux Sound Architecture Driver Version 1.0.24.
    PCI host bridge to bus 0000:00
    pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
    pci_bus 0000:00: root bus resource [io  0x0400-0x83ff]
    PCI host bridge to bus 0000:01
    pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
    pci_bus 0000:01: root bus resource [io  0x8400-0x87ff]
    PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
    pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
    pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
    Bluetooth: Core ver 2.16
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: SCO socket layer initialized
    cfg80211: Calling CRDA to update world regulatory domain
    Switching to clocksource upg
    FS-Cache: Loaded
    NET: Registered protocol family 2
    IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    TCP: Hash tables configured (established 16384 bind 16384)
    TCP reno registered
    UDP hash table entries: 256 (order: 1, 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    FS-Cache: Netfs 'nfs' registered for caching
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    FS-Cache: Netfs 'cifs' registered for caching
    NTFS driver 2.1.30 [Flags: R/O].
    fuse init (API version 7.18)
    msgmni has been set to 568
    io scheduler noop registered
    io scheduler cfq registered (default)
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
    console [ttyS0] enabled
    serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
    serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
    loop: module loaded
    brcm-pm: enabling sata clocks
    PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
    scsi0 : sata_brcmstb
    scsi1 : sata_brcmstb
    ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
    ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
    Broadcom STB NAND controller (BrcmNand Controller)
    bcmemac: Broadcom STB 10/100 EMAC driver v3.0
    bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:03:00:01:49:df)
    bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
    usbcore: registered new interface driver zd1201
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    brcm-pm: enabling usb clocks
    ehci-brcm ehci-brcm.0: Broadcom STB EHCI
    ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
    ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
    ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ehci-brcm ehci-brcm.1: Broadcom STB EHCI
    ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
    ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
    ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    ohci-brcm ohci-brcm.0: Broadcom STB OHCI
    ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
    ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    ohci-brcm ohci-brcm.1: Broadcom STB OHCI
    ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
    ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    ata1: SATA link down (SStatus 4 SControl 300)
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    lirc_dev: IR Remote Control driver registered, major 254
    IR NEC protocol handler initialized
    IR RC5(x) protocol handler initialized
    IR RC6 protocol handler initialized
    IR JVC protocol handler initialized
    IR Sony protocol handler initialized
    IR RC5 (streamzap) protocol handler initialized
    IR SANYO protocol handler initialized
    IR MCE Keyboard/mouse protocol handler initialized
    IR LIRC bridge handler initialized
    usbcore: registered new interface driver btusb
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    ALSA device list:
      No soundcards found.
    TCP cubic registered
    NET: Registered protocol family 17
    Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    lib80211: common routines for IEEE802.11 drivers
    EBI CS1: setting up NAND flash (primary)
    mtd->oobsize=0, mtd->eccOobSize=0
    NAND_CS_NAND_XOR=00000000
    B4: NandSelect=50000202, nandConfig=15142200, chipSelect=1
    brcmnand_read_id: CS1: dev_id=92f18095
    After: NandSelect=50000202, nandConfig=15142200
    DevId 92f18095 may not be supported.  Will use config info
    Spare Area Size = 16B/512B
    Block size=00020000, erase shift=17
    NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
    busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
    timing1 not adjusted: 5363444f
    timing2 not adjusted: 00000fc6
    ECC level changed to 15
    OOB size changed to 16
    BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS1
    
    Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=92f18095, tim1=5363444f, tim2=00000fc6
    BrcmNAND version = 0x0302 128MB @00000000
    B4: NandSelect=50000202, nandConfig=15142200, chipSelect=1
    brcmnand_read_id: CS1: dev_id=92f18095
    After: NandSelect=50000202, nandConfig=15142200
    Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
    brcmnand_scan: B4 nand_select = 50000202
    brcmnand_scan: After nand_select = 50000202
    page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
    Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
    ECC layout=brcmnand_oob_bch4_4k
    brcmnand_scan:  mtd->oobsize=64
    brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
    brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
    -->brcmnand_default_bbt
    brcmnand_default_bbt: bbt_td = bbt_main_descr
    Adjust partition complete size from entire device to 100000 to avoid overlap with BBT reserved space
    Creating 3 MTD partitions on "brcmnand.0":
    0x000000000000-0x000007a00000 : "rootfs"
    0x000007a00000-0x000007e00000 : "kernel"
    0x000007e00000-0x000007f00000 : "complete"
    UBI: attaching mtd0 to ubi0
    UBI: physical eraseblock size:   131072 bytes (128 KiB)
    UBI: logical eraseblock size:    126976 bytes
    UBI: smallest flash I/O unit:    2048
    UBI: VID header offset:          2048 (aligned 2048)
    UBI: data offset:                4096
    ata2: SATA link down (SStatus 4 SControl 300)
    UBI: max. sequence number:       0
    UBI error: ubi_wl_init_scan: no enough physical eraseblocks (0, need 1)
    UBI error: ubi_init: cannot attach mtd0
    VFS: Cannot open root device "ubi0:rootfs" or unknown-block(8,1)
    Please append a correct "root=" boot option; here are the available partitions:
    1f00          124928 mtdblock0  (driver?)
    1f01            4096 mtdblock1  (driver?)
    1f02            1024 mtdblock2  (driver?)
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)

    wie kann ich den Fehler beseitigen?

  3. #3
    Senior Mitglied Avatar von sirtobie
    Registriert seit
    05.02.2017
    Ort
    zuhause
    Beiträge
    257
    Total Downloaded
    0
    Total Downloaded
    0
    ReceiverDankeAktivitäten
    Box 1:
    Edision OS-Mega (OpenATV)
     
     
    Box 2:
    Edision Argus Pingulux (NHD)
     
     
    Box 3:
    Samsung UE40C7700 (DeltaCam)
     
     
    Zu wenig Flash. Versuch mal einen Sprinter in einen Smart zu quetschen.
    VG
    sirtobie
    __________________________________________________ ___________________________________________
    Samsung UE40C7700 + DeltaCam Twin
    Edision OS Mega (OpenATV)
    Edision Argus Pingulux (NHD)


  4. #4
    Senior Mitglied Avatar von satfreund
    Registriert seit
    17.08.2016
    Ort
    nördliches OWL
    Beiträge
    1.682
    Total Downloaded
    13,50 MB
    Total Downloaded
    13,50 MB
    ReceiverDankeAktivitäten
    Box 1:
    Zgemma H7S OATV 6.3+6.4
     
     
    Box 2:
    AX Hd51 4k OATV 6.3+6.4
     
     
    Box 3:
    DM 8000 OATV 6.4
     
     
    @sirtobie
    .................................................. .................................................. .................................................. .................
    Anhang 63082
    Die Erde ist eine

  5. #5
    Anfänger
    Registriert seit
    23.12.2013
    Beiträge
    12
    Total Downloaded
    2,50 MB
    Total Downloaded
    2,50 MB
    ReceiverDankeAktivitäten
    Ok, danke für die Aufklärung, eben auf 6.2 gewechselt, funktioniert nun


Stichworte

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
Diese Website benutzt Cookies
Wir benutzen Cookies um Sitzungsinformationen zu speichern. Dies erleichtert es uns z.B. Dich an Deine Login zu erinnern, Einstellungen der Webseite zu speichern, Inhalte und Werbung zu personalisieren, Social Media Funktionen anzubieten und unser Datenaufkommen zu analysieren. Wir teilen diese Informationen ebenfalls mit unseren Social Media-, Werbe- und Analysepartnern.
     
Alle Zeitangaben in WEZ +1. Es ist jetzt 01:47 Uhr.
Powered by vBulletin® Version 4.2.5 (Deutsch)
Copyright ©2020 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.
Resources saved on this page: MySQL 11,76%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
vBulletin Skin By: PurevB.com