Ergebnis 1 bis 8 von 8
-
04.07.2019, 19:03 #1
- Registriert seit
- 06.01.2015
- Beiträge
- 246
- Thanks (gegeben)
- 73
- Thanks (bekommen)
- 8
- Total Downloaded
- 51,05 MB
- Total Downloaded
- 51,05 MB
Box 1:Gigablue UHD Quad 4KBox 2:Gigablue UHD Trio 4KDreambox 520 bootet nicht mehr. LED nur noch rot
Hallo,
ich habe ein Problem mit meiner Dreambox. Beim Einschalten leuchtet nur noch die rote LED. Mehr kommt nicht kein Blinken usw. Hier mal der Bootlog:
Code:=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.07.04 19:00:28 =~=~=~=~=~=~=~=~=~=~=~= Dreambox DM5 20 M0CZS L2=1 LLMB=1 BrCfg=E30FB7C6 #@ BCM973625A0 CFE v15.3, Endian Mode: Little Build Date: Fri Aug 19 11:48:16 2016 (Jann@Cynric) Copyright (C) Broadcom Corporation. Non-CI box detected card if inited Enabling NAND flash at CS2: A5U4GA31ATS(DEVICE ID=0xC8DC9095), ECC Level=4, Spare Area Size=16 MACRONIX SPI flash detected: Size = 16MB, Sector Size 4096, Page Size 256 CPU speed: 751MHz DDR Frequency: 1061 MHz DDR Mode: DDR3 Total memory(MEMC 0): 512MB MEMC 0 DDR Width: 16 Boot Device: SPI Total flash: 16MB RTS VERSION: rts_hevc10_1067 ETH0_PHY: INT ETH0_MDIO_MODE: 1 ETH0_SPEED: 100 ETH0_PHYADDR: 1 DM init finalization yxml: processing file of 131072 bytes... succeeded! no file loaded, create xml restoring default xml loaded network params of: DHCP, 192.168.0.219, 255.255.255.0, 192.168.0.1 [1] type 3, dev nandflash0.kernel, loader elf, filesys raw, file , options [2] type 3, dev flash0.kernel, loader elf, filesys raw, file , options [3] type 1, dev eth0, loader elf, filesys tftp, file , options bmem=192M@64M console=ttyS0,1000000 root=/dev/nfs ip=dhcp added 3 sources to autoboot list init fp Initializing USB. CFE initialized. found card in unknown state ca valid! ***** DREAMBOX SSBL ***** Not interrupted yet, trying autoboot or rescue loader, hit any key in the next 500ms to cancel Proceeding with autoboot.. You can try aborting with Ctrl+C *** Autoboot: Trying device 'nandflash0.kernel' file (raw,elf) Ethernet Cable unplugged Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options: Loading: 0x80001000/8550592 0x808288c0/257696 Entry address is 0x806854f0 Closing network eth0 Starting program at 0x806854f0 [ 0.264000] console [ttyS0] enabled, bootconsole disabled [ 0.264000] console [ttyS0] enabled, bootconsole disabled [ 0.269000] loop: module loaded [ 0.270000] brcmstb_nand: NAND controller driver is loaded [ 0.392000] bcmgenet: configuring instance #0 for internal PHY [ 0.412000] bcmgenet bcmgenet.0: (unregistered net_device): link down [ 0.413000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.414000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI [ 0.414000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 [ 0.446000] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300 [ 0.452000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00 [ 0.453000] hub 1-0:1.0: USB hub found [ 0.453000] hub 1-0:1.0: 2 ports detected [ 0.454000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.455000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI [ 0.455000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2 [ 0.456000] ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400 [ 0.522000] hub 2-0:1.0: USB hub found [ 0.523000] hub 2-0:1.0: 2 ports detected [ 0.523000] Initializing USB Mass Storage driver... [ 0.524000] usbcore: registered new interface driver usb-storage [ 0.525000] USB Mass Storage support registered. [ 0.525000] i2c /dev entries driver [ 0.526000] lirc_dev: IR Remote Control driver registered, major 253 [ 0.526000] usbcore: registered new interface driver btusb [ 0.528000] TCP: cubic registered [ 0.528000] NET: Registered protocol family 10 [ 0.530000] NET: Registered protocol family 17 [ 0.531000] Bluetooth: RFCOMM TTY layer initialized [ 0.531000] Bluetooth: RFCOMM socket layer initialized [ 0.532000] Bluetooth: RFCOMM ver 1.11 [ 0.532000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 0.533000] Bluetooth: BNEP filters: protocol multicast [ 0.533000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.534000] L2TP core driver, V2.0 [ 0.535000] Registering the dns_resolver key type [ 0.535000] PM: CP0 COUNT/COMPARE frequency does not depend on divisor [ 0.537000] EBI CS2: setting up NAND flash (primary) [ 0.538000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xdc (Unknown NAND 512MiB 3,3V 8-bit) [ 0.539000] brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4 [ 0.539000] [ 0.541000] Bad block table found at page 262080, version 0x01 [ 0.542000] Bad block table found at page 262016, version 0x01 [ 0.543000] nand_read_bbt: bad block at 0x000000400000 [ 0.544000] nand_read_bbt: bad block at 0x000018e40000 [ 0.545000] nand_read_bbt: bad block at 0x000018ec0000 [ 0.545000] nand_read_bbt: bad block at 0x000019a00000 [ 0.546000] nand_read_bbt: bad block at 0x000019d60000 [ 0.547000] Creating 3 MTD partitions on "brcmnand.0": [ 0.548000] 0x000000000000-0x00001f500000 : "rootfs" [ 0.550000] 0x000000000000-0x000020000000 : "entire_device" [ 0.552000] 0x00001f500000-0x00001fa00000 : "kernel" [ 0.553000] EBI CS0: setting up SPI flash [ 0.554000] spi_brcmstb spi_brcmstb.0: 1-lane output, 3-byte address [ 0.555000] spi_brcmstb spi_brcmstb.0: master is unqueued, this is deprecated [ 0.556000] m25p80 spi0.0: found mx25l12805d, expected w25q128bv [ 0.556000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.558000] UBI: attaching mtd0 to ubi0 [ 0.559000] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 0.560000] UBI: logical eraseblock size: 126976 bytes [ 0.560000] UBI: smallest flash I/O unit: 2048 [ 0.561000] UBI: VID header offset: 2048 (aligned 2048) [ 0.561000] UBI: data offset: 4096 [ 3.692000] UBI: max. sequence number: 13781 [ 3.707000] UBI: attached mtd0 to ubi0 [ 3.708000] UBI: MTD device name: "rootfs" [ 3.709000] UBI: MTD device size: 501 MiB [ 3.709000] UBI: number of good PEBs: 4003 [ 3.710000] UBI: number of bad PEBs: 5 [ 3.710000] UBI: number of corrupted PEBs: 0 [ 3.711000] UBI: max. allowed volumes: 128 [ 3.711000] UBI: wear-leveling threshold: 4096 [ 3.712000] UBI: number of internal volumes: 1 [ 3.712000] UBI: number of user volumes: 1 [ 3.713000] UBI: available PEBs: 0 [ 3.713000] UBI: total number of reserved PEBs: 4003 [ 3.714000] UBI: number of PEBs reserved for bad PEB handling: 40 [ 3.715000] UBI: max/mean erase counter: 8/4 [ 3.715000] UBI: image sequence number: 1657856541 [ 3.716000] UBI: background thread "ubi_bgt0d" started, PID 55 [ 3.718000] ALSA device list: [ 3.718000] No soundcards found. [ 3.770000] UBIFS: recovery needed [ 3.826000] UBIFS: recovery completed [ 3.826000] UBIFS: mounted UBI device 0, volume 0, name "dreambox-rootfs" [ 3.827000] UBIFS: file system size: 500793344 bytes (489056 KiB, 477 MiB, 3944 LEBs) [ 3.828000] UBIFS: journal size: 25014272 bytes (24428 KiB, 23 MiB, 197 LEBs) [ 3.829000] UBIFS: media format: w4/r0 (latest is w4/r0) [ 3.830000] UBIFS: default compressor: lzo [ 3.830000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 3.832000] VFS: Mounted root (ubifs filesystem) on device 0:12. [ 3.832000] devtmpfs: error mounting -2 [ 3.833000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance. [ 3.834000] Rebooting in 180 seconds..
-
Advertising
-
06.07.2019, 11:22 #2
- Registriert seit
- 08.04.2014
- Beiträge
- 968
- Thanks (gegeben)
- 77
- Thanks (bekommen)
- 164
- Total Downloaded
- 278,51 MB
- Total Downloaded
- 278,51 MB
Box 1:VU+ Duo 4K DVB-C FBCDie Box scheitert beim Mount, schon Neuflash probiert?
-
06.07.2019, 12:17 #3
- Registriert seit
- 28.04.2018
- Ort
- Wollt Ihr nicht wissen(Oje!)
- Beiträge
- 276
- Thanks (gegeben)
- 48
- Thanks (bekommen)
- 75
- Total Downloaded
- 175,2 KB
- Total Downloaded
- 175,2 KB
Box 1:DM 920 UHD die II (Master) oATV 7.3Box 2:DRAKE ESR 2000XT(AZ/EL Slave)Box 3:Spectra Explorer by Waveline(Sat-Spektrum Receiver)Ich habe über METAGER(Rechenzentrum Hannover), eine Metasuchmaschine, nach "BAD BLOCK TABLE FOUND" gesucht, da sind einige Lösungsansätze, aber leider in Englisch. Ich hatte sowas ähnliches schonmal unter LINUX MINT, wie sich dann herrausstellte war ein RAM-Riegel Schrott.
C.
-
06.07.2019, 13:07 #4
- Registriert seit
- 03.04.2013
- Beiträge
- 14.861
- Thanks (gegeben)
- 763
- Thanks (bekommen)
- 21090
- Total Downloaded
- 162,47 MB
- Total Downloaded
- 162,47 MB
wie siehts aus Dream Original Image schon mal Probiert ?, wenn das Klappt dann noch mal das openATV Installieren
wenn auch das Dreambox Original Image nicht geht bei Dream RMA holen wenn noch Garantie hast sonst siehst es schlecht aus.
openATV we are open Source
Boykott GPL violator
-
Danke - 1 ThanksFreak2 bedankten sich
-
07.07.2019, 10:15 #5
- Registriert seit
- 06.01.2015
- Beiträge
- 246
- Thanks (gegeben)
- 73
- Thanks (bekommen)
- 8
- Total Downloaded
- 51,05 MB
- Total Downloaded
- 51,05 MB
ThemenstarterBox 1:Gigablue UHD Quad 4KBox 2:Gigablue UHD Trio 4KWenn ich die Box einschalte leuchten kurz die Lan Leds, dann gehen diese aus und auch nicht wieder an. Komme per Netzwerk und per gedrückter PowerTaste nicht in den RescueMode!
-
07.07.2019, 13:40 #6satfreundGast
-
Danke - 1 ThanksFreak2 bedankten sich
-
07.07.2019, 14:09 #7
- Registriert seit
- 17.06.2013
- Beiträge
- 1.788
- Thanks (gegeben)
- 1750
- Thanks (bekommen)
- 674
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Vu+ Uno 4K SE und Vu+ Duo 4K SEBox 2:Zgemma H7S und verkauft H7CBox 3:Verkauft: Vu+ Solo 4KBox 4:Verkauft: Zgemma H9 Twin und ComboBox 5:Verkauft: Dreambox One und TwoUnd im schlimmsten Fall dann auf eine 3...6...9... Wochen dauernde Reparatur warten.
Wenn der Receiver noch nicht mehr als vor 6 Monaten gekauft wurde, beim Verkäufer reklamieren und Reparatur oder Austausch innerhalb von maximal einer Woche fordern. Falls innerhalb einer Woche keine Reparatur oder ein Austausch des Receivers möglich ist, die Rückabwicklung des Kaufvertrages gegen volle Kostenerstattung fordern! Ein Receiver ist ein Alltagsgegenstand, den man auch täglich nutzen können muss. Da ist eine Woche Nichtbenutzbarkeit schon die oberste Grenze des Vertretbarem.Frei nach dem bekanntem Sprichwort "Gut Ding will Weile haben":
Gute Receiver brauchen Zeit, schlechte einen werbewirksamen Hype!
-
Danke - 1 ThanksFreak2 bedankten sich
-
08.07.2019, 12:51 #8
- Registriert seit
- 06.01.2015
- Beiträge
- 246
- Thanks (gegeben)
- 73
- Thanks (bekommen)
- 8
- Total Downloaded
- 51,05 MB
- Total Downloaded
- 51,05 MB
ThemenstarterBox 1:Gigablue UHD Quad 4KBox 2:Gigablue UHD Trio 4KDanke für eure Antworten, habe das Gerät jetzt eingeschickt!
PS.: Bei der Reparatur würde das Mainboard getauscht. Box läuft jetzt wieder.Geändert von Freak2 (17.07.2019 um 20:32 Uhr)
Lesezeichen