Ergebnis 31 bis 40 von 97
-
15.06.2015, 19:39 #31
- Registriert seit
- 14.06.2015
- Beiträge
- 13
- Thanks (gegeben)
- 0
- Thanks (bekommen)
- 0
- Total Downloaded
- 10,35 MB
- Total Downloaded
- 10,35 MB
Das Teil nennt sich in der Systemsteuerung "Silicon Labs CP210x USB to UART Bridge"
Das Teil hat 5 Anschlüsse
T, R, G, 3,3V und 5V
Angeschlossen habe ich wie folgt:
Kabel <-> AZBox Premium
T <-> R
R<-> T
G<-> G
Port Settings im Gerätemanager:
115200
Data Bits 8
Parität None
Stop Bits 1
Flow Control None
Ich habe nur den Putty installiert.
Sobald ich die AZBox starte beginnt sofort der Putty zu antworten. Einen Abbruch durch ctrl +c ist nicht möglich
Ich weiß nicht weiter.
Vergesse ich etwas?
-
Advertising
-
15.06.2015, 20:11 #32
- Registriert seit
- 24.06.2013
- Ort
- Österreich
- Beiträge
- 5.027
- Thanks (gegeben)
- 837
- Thanks (bekommen)
- 1492
- Total Downloaded
- 15,72 MB
- Total Downloaded
- 15,72 MB
Box 1:Zgemma H9.TwinBox 2:Edision Optimuss OS1+Box 3:Golden Interstar XPEED LX1Box 4:SpycatBox 5:AX HD60Evtl. funzt tatsächlich dein transmit vom PC nicht. Schaue mal ob die Klemmen richtig gut rein gesteckt sind. Natürlich könnte auch das Teil kaputt sein.
Deine Einstellungen und Anschlüße sollten so passen.______________________
Hans
TV - Hisense Ulra HD
Eutelsat 13°E und Astra 19,2°E Unicable-Matrix mit Wide-LNB
-
16.06.2015, 03:46 #33
- Registriert seit
- 26.07.2013
- Ort
- Austria
- Beiträge
- 488
- Thanks (gegeben)
- 225
- Thanks (bekommen)
- 116
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Edision Optimus OS2+Box 2:Edision Optimus OS2+Box 3:Octagon SF8008 Mini 4KWie zeini schon sagte, Einstellungen und Anschlüsse sind ok. Ich selbst verwende einen Umsetzer mit Prolific 2303 PL2303 Chip und der funktioniert einwandfrei.
Lade Dir mal den neuesten Treiber für Dein Betriebssystem und Deinen Chipsatz herunter.
Deaktiviere die Firewall und den Virenscanner auf Deinem Rechner.
Sollte das nicht funktionieren, würde ich Dir empfehlen, es mit einem anderen Umetzer zu versuchen.Ich habe keine Lösung, aber ich bewundere das Problem.
-
16.06.2015, 07:16 #34
- Registriert seit
- 14.06.2015
- Beiträge
- 13
- Thanks (gegeben)
- 0
- Thanks (bekommen)
- 0
- Total Downloaded
- 10,35 MB
- Total Downloaded
- 10,35 MB
Hat leider alles nicht geklappt.
Welcher Umsetzer ist denn zu empfehlen?
-
16.06.2015, 08:27 #35
- Registriert seit
- 26.07.2013
- Ort
- Austria
- Beiträge
- 488
- Thanks (gegeben)
- 225
- Thanks (bekommen)
- 116
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Edision Optimus OS2+Box 2:Edision Optimus OS2+Box 3:Octagon SF8008 Mini 4KHIER sollte schon ein passender dabei sein. Nimm einen mit PL2303 Chipsatz. Der funktioniert bei mir mit Win7 wunderbar.
Achja, welchses Bestriebssystem verwendest Du denn?
Teste doch mal, ob Du mit einer Linux LiveCD bzw. DVD Eingaben mit Putty auf der Box machen kannst.Ich habe keine Lösung, aber ich bewundere das Problem.
-
18.06.2015, 16:21 #36
- Registriert seit
- 14.06.2015
- Beiträge
- 13
- Thanks (gegeben)
- 0
- Thanks (bekommen)
- 0
- Total Downloaded
- 10,35 MB
- Total Downloaded
- 10,35 MB
Super Hilfe!!!
Es lag am Stecker
Mit dem neuen Stecker kann ich jetzt in der Yamon Konsole endlich Befehle eingeben.
Kann ich hier noch was falsch machen?
Ich habe unterschiedliche Anleitungen im Netz gefunden, und bin daher gerade ein bisschen unsicher.
Ist es Sinnvoll erst zurück auf die Original Firmware zu gehen oder kann ich gleich openrsi ect.. versuchen?
-
18.06.2015, 17:59 #37
- Registriert seit
- 26.07.2013
- Ort
- Austria
- Beiträge
- 488
- Thanks (gegeben)
- 225
- Thanks (bekommen)
- 116
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Edision Optimus OS2+Box 2:Edision Optimus OS2+Box 3:Octagon SF8008 Mini 4KWelche Anleitungen hast Du denn? Im Grunde genommen funktionieren die Meisten. Halt Dich genau an die Anweisungen. Du musst nicht zwingend auf die Originale zurück. backup_kernel_3_4_4 ist z.B. schon ein E2 Kernel. Der ohne Zahlen dahinter ist von OpenSat. Ich hab noch einen, den hab ich mir aus dem Patchfile von Os2E2 extrahiert. Mit dem bootet die Box dann gleich in den RescueMode.
Ich habe keine Lösung, aber ich bewundere das Problem.
-
18.06.2015, 19:24 #38
- Registriert seit
- 26.07.2013
- Ort
- Austria
- Beiträge
- 488
- Thanks (gegeben)
- 225
- Thanks (bekommen)
- 116
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Edision Optimus OS2+Box 2:Edision Optimus OS2+Box 3:Octagon SF8008 Mini 4KIch hab Dir hier noch den Kernel von Os2E2 hochgeladen, falls Du den verwenden willst.
Kernel_Os2E2.zipIch habe keine Lösung, aber ich bewundere das Problem.
-
18.06.2015, 22:01 #39
- Registriert seit
- 14.06.2015
- Beiträge
- 13
- Thanks (gegeben)
- 0
- Thanks (bekommen)
- 0
- Total Downloaded
- 10,35 MB
- Total Downloaded
- 10,35 MB
hmm
ich bleibe beim Login hängen,
den bekomme ich nicht
Ich kann somit die Anleitung nicht zu Ende führen.
Kann es sein, dass die Datei die falsche ist. Sie ist auch nur knapp 6,6 MB groß
YAMON> load -b tftp://192.168.1.62/vmlinux.bin 0x90020000
About to load tftp://192.168.1.62/vmlinux.bin
Press Ctrl-C to break
.................................................. ..............
.................................................. ..............
.................................................. ..............
...............
Start = 0x90020000, range = (0x90020000,0x9069dbff), format = BINARY
Length = 0x67dc00 (6806528)
Checksum = 0x113ef7aa
YAMON> go
em86xx_eth ethernet stop
* Exception (user) : Reserved instruction *
BadVAddr = 0x0288029d Cause = 0x30800028
Compare = 0xffffffff Config = 0x80200483
Config1 = 0xbed96c8e Config2 = 0x80000000
Config3 = 0x00000020 Context = 0x08014400
Count = 0x0bc3a403 DEPC = 0x27e00403
Debug = 0x0e011410 EBase = 0x91000000
EPC = 0x90020000 EntryHi = 0x9007c000
EntryLo0 = 0x00000000 EntryLo1 = 0x00000000
ErrorEPC = 0x88242000 HWREna = 0x00000000
Index = 0x80000000 IntCtl = 0x00000000
PRId = 0x00019069 PageGrain = 0x00000000
PageMask = 0x00000000 Random = 0x0000000e
SRSCtl = 0x00000000 SRSMap = 0x00000000
Status = 0x00009c02 WatchHi = 0x80000000
WatchLo = 0x00000000 Wired = 0x00000000
Hi = 0x00000023 Lo = 0x43958125
$ 0(zr):0x00000000 $ 8(t0):0x00000000 $16(s0):0x00000000 $24(t8):0x00000000
$ 1(at):0x00000000 $ 9(t1):0x00000000 $17(s1):0x00000000 $25(t9):0x00000000
$ 2(v0):0x00000000 $10(t2):0x00000000 $18(s2):0x00000000 $26(k0):0x00000000
$ 3(v1):0x00000000 $11(t3):0x00000000 $19(s3):0x00000000 $27(k1):0x910f8f20
$ 4(a0):0x00000001 $12(t4):0x00000000 $20(s4):0x00000000 $28(gp):0x00000000
$ 5(a1):0x910fa220 $13(t5):0x00000000 $21(s5):0x00000000 $29(sp):0x91105520
$ 6(a2):0x9107b4f8 $14(t6):0x00000000 $22(s6):0x00000000 $30(s8):0x91105520
$ 7(a3):0x10000000 $15(t7):0x00000000 $23(s7):0x00000000 $31(ra):0x91045614
em86xx_eth ethernet start
YAMON>
-
19.06.2015, 03:33 #40
- Registriert seit
- 26.07.2013
- Ort
- Austria
- Beiträge
- 488
- Thanks (gegeben)
- 225
- Thanks (bekommen)
- 116
- Total Downloaded
- 0
- Total Downloaded
- 0
Box 1:Edision Optimus OS2+Box 2:Edision Optimus OS2+Box 3:Octagon SF8008 Mini 4KDie Ausgaben bitte als Code eingeben.
Nach YAMON>go sollte das dann so aussehen.
Code:About to load tftp://192.168.1.6/vmlinux.bin Press Ctrl-C to break ................................................................ ................................................................ ................................................................ ................................................................ ....................................... Start = 0x90020000, range = (0x90020000,0x9095880f), format = BINARY Length = 0x938810 (9668624) Checksum = 0x2254194d YAMON> go em86xx_eth ethernet stop Linux version 2.6.22.19-19-the_ripper (root@debian) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #185 PREEMPT Mon May 31 16:44:40 CEST 2010 Configured for SMP863x (revision ES6+/RevA+), detected SMP8634 (revision ES9/RevC). Detected CPU/System/DSP Frequencies: 300.37/200.25/300.37MHz SMP86xx Enabled Devices under Linux/XENV 0x48000000 = 0x00021ace BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD Valid MEMCFG found at 0x10000fc0. CPU revision is: 00019069 Determined physical RAM map: memory: 06be0000 @ 10020000 (usable) User-defined physical RAM map: memory: 06ae0000 @ 10020000 (usable) Wasting 2098176 bytes for tracking 65568 unused pages Initrd not found or empty - disabling initrd On node 0 totalpages: 92928 DMA zone: 726 pages used for memmap DMA zone: 0 pages reserved DMA zone: 92202 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Built 1 zonelists. Total pages: 92202 Kernel command line: mem=107m console=ttyS0,115200 Primary instruction cache 16kB, 2-way, physically tagged, linesize 16 bytes. Primary data cache 16kB, 2-way, virtually tagged, cache aliases, linesize 16 bytes Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 2048 (order: 11, 8192 bytes) Using 150.188 MHz high precision timer. Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 96384k/109440k available (4018k kernel code, 12948k reserved, 1013k data, 4408k init, 0k highmem) Calibrating delay loop... 295.93 BogoMIPS (lpj=147968) Mount-cache hash table entries: 512 NET: Registered protocol family 16 tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x08000000. PCI: Initializing SMP86xx PCI host controller PCI: Remapped PCI I/O space 0x58000000 to 0xc8020000, size 64 kB PCI: Remapped PCI config space 0x50000000 to 0xc8004000, size 10 kB PCI: device 1 disabled PCI: device 4 disabled PCI: Configured SMP86xx as PCI slave with 128MB PCI memory PCI: Region size is 16384KB PCI: Map DMA memory 0x10020000-0x16b00000 for PCI at 0x11000000 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: TANGOX clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered Created /proc/cpucache_info entry. Tango2 frequency scaling module installed. NTFS driver 2.1.28 [Flags: R/W DEBUG]. JFFS2 version 2.2. © 2001-2006 Red Hat, Inc. fuse init (API version 7.8) SGI XFS with large block numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A loop: module loaded nbd: registered device at major 43 tango2_enet: ethernet driver for SMP863x internal mac tango2_enet: detected phy at address 0x01 tango2_enet: mac address 00:02:14:14:41:ba Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: SMP86xx Bus Mastering IDE controller Probing IDE interface ide0... hda: KingSpec KDM-40VS.2-008GMS, ATA DISK drive hda: no 80 conductors cable, falling back to lower udma mode hda: selected mode 0x42 hda: set to Ultra DMA mode 2 ide0: DMA enabled for ATA DISK hda ide0 at 0x223c0-0x223c7,0x22398 on irq 26 hda: max request size: 128KiB hda: 15662304 sectors (8019 MB) w/1KiB Cache, CHS=15538/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 hda3 hda4 < hda5 > QLogic Fibre Channel HBA Driver physmap flash device CS2: 0x800000 at 0x48000000 CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Using physmap partition definition Adding partition #1-#5 Creating 5 MTD partitions on "CS2: Physically mapped flash": 0x00000000-0x00020000 : "CS2-Part1" 0x00020000-0x00040000 : "CS2-Part2" 0x00040000-0x00080000 : "CS2-Part3" 0x00080000-0x00700000 : "CS2-Part4" 0x00700000-0x00800000 : "CS2-Part5" PCI: Enabling device 0000:00:02.2 (0000 -> 0002) ehci_hcd 0000:00:02.2: EHCI Host Controller ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.2: irq 22, io mem 0x62008000 ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected driver tangox-ehci-hcd, 10 Dec 2004 TangoX USB initializing... tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0 tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 2 tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021400 tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 4408k freed Algorithmics/MIPS FPU Emulator v1.5 Initializing random number generator... done. Starting network... ip: RTNETLINK answers: File exists eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 udhcpc (v1.16.1) started Sending discover... Sending discover... Sending select for 192.168.1.9... Lease of 192.168.1.9 obtained, lease time 86400 deleting routers route: SIOCDELRT: No such process adding dns 192.168.1.1 adding dns 192.168.1.1 ===> Starting services... [TD210] INITIALIZED END Fail to Receive ACK 00 [TD210] SLEEP MODE OFF Fail to Receive ACK 00 Fail to Receive ACK 00 Fail to Receive ACK 00 Fail to Receive ACK 00 Fail to Receive ACK 00 ===> [1] telnetd starting... ===> [2] mounting DOM ... mount: mounting /dev/hda1 on /MMP failed: Invalid argument mount: mounting /dev/hda2 on /PLUGINS failed: Invalid argument mount: mounting /dev/hda3 on /DISK2 failed: Invalid argument attempt to access beyond end of device hda4: rw=0, want=4, limit=2 EXT3-fs: unable to read superblock mount: mounting /dev/hda4 on /Download failed: Invalid argument cp: can't stat '/DISK1/.passwd': No such file or directory cp: can't stat '/DISK1/.shadow': No such file or directory insmod: can't read '/MMP/modules/2.6.22/llad.ko': No such file or directory insmod: can't read '/MMP/modules/2.6.22/em8xxx.ko': No such file or directory ===> Starting vsftpd... AZBOX login: login[702]: root login on 'pts/0' root login[698]: root login on 'ttyS0'
vmlinux.zipIch habe keine Lösung, aber ich bewundere das Problem.
Lesezeichen