Ergebnis 1 bis 8 von 8
  1. #1
    Senior Mitglied
    Registriert seit
    03.03.2015
    Ort
    Bayern
    Beiträge
    141
    Thanks (gegeben)
    65
    Thanks (bekommen)
    15
    Total Downloaded
    21,15 MB
    Total Downloaded
    21,15 MB
    ReceiverDanke
    Box 1:
    DM920 1x DVB-S2X FBC, 1x Dual DVB-S2
     
     
    Box 2:
    Xpeed LX3 4x DVB-S2
     
     
    Box 3:
    GM Triplex T2
     
     

    Image 4.2 Kein Bild nach dem Booten beim GM Triplex

    Hi,

    wollte mal das 4.2 testen, da fiel mir auf, dass nach dem Booten kein Bild erscheint, nur das Bootlogo.
    Ton ist vorhanden, evtl. programmierte Aufnahmen gehen auch.
    Nach 3-4x umschalten kommt ein Bild.
    Beim 5.1 läuft alles normal.

    Ein Bootlog habe ich nicht, aber die Ausgabe von dmesg:
    (Die Ausgabe ist vom 4.2 vom 13.02.2014, ohne Settingsübernahme oder Installationen)

    Code:
    root@sparktriplex:~# dmesg
    : TMU1 kept as earlytimer
    STMicroelectronics - Coprocessors st231 Init
    st231.0 Coprocessor -------------------------------------------
        flags 0001 RAM start at 0xa0000000  size      0x00400000
                      cop. addr 0x40000000
        Channels : Not defined
        IRQ      : not used
    ---------------------------------------------------------------
    st231.1 Coprocessor -------------------------------------------
        flags 0001 RAM start at 0xa0400000  size      0x00400000
                      cop. addr 0x40400000
        Channels : Not defined
        IRQ      : not used
    ---------------------------------------------------------------
    DMA: Registering fdma_dmac.0 handler (16 channels).
    IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
    stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7105_0.elf
    DMA: Registering fdma_dmac.1 handler (16 channels).
    platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.1
    IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
    stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7105_1.elf
    stm-rng hardware driver 1.0 configured
    platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.5
    Advanced Linux Sound Architecture Driver Version 1.0.21.
    ALSA device list:
      #0: STMicroelectronics STx7105 cut 4.x SOC audio subsystem
    TCP cubic registered
    NET: Registered protocol family 10
    NET: Registered protocol family 17
    lib80211: common routines for IEEE802.11 drivers
    lib80211_crypt: registered algorithm 'NULL'
    NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
    stm-nand-flex: Using platform timing data
    Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    stm-nand-flex: Using boot partition name [uboot] (from kernel config)
    usb 1-1: new high speed USB device using stm-ehci and address 2
    cmdlinepart partition parsing not available
    Creating 7 MTD partitions on "stm-nand-flex.0":
    0x000000000000-0x000000100000 : "uboot"
    0x000000100000-0x000000b00000 : "Spark kernel"
    0x000000b00000-0x000001200000 : "Reserve0"
    0x000001200000-0x000001400000 : "Reserve1"
    0x000001400000-0x000018000000 : "Spark Userfs"
    0x000018000000-0x000018800000 : "kernel"
    0x000018800000-0x00001ff00000 : "rootfs"
    stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
    boot-ECC 0x00000000->0x00100000
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    usb 1-1.4: new high speed USB device using stm-ehci and address 3
    eth0: device MAC address 30:00:07:00:29:56
     No MAC Management Counters available
    usb 1-1.4: configuration #1 chosen from 1 choice
    scsi1 : SCSI emulation for USB Mass Storage devices
    usb-storage: device found at 3
    usb-storage: waiting for device to settle before scanning
    IP-Config: Complete:
         device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
         host=Enigma2, domain=, nis-domain=(none),
         bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
    PHY: 0:02 - Link is Up - 100/Full
    scsi 1:0:0:0: Direct-Access     TOSHIBA  External USB 3.0 0    PQ: 0 ANSI: 6
    sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    usb-storage: device scan complete
    sd 1:0:0:0: [sda] Write Protect is off
    sd 1:0:0:0: [sda] Mode Sense: 43 00 00 00
    sd 1:0:0:0: [sda] Assuming drive cache: write through
    sd 1:0:0:0: [sda] Assuming drive cache: write through
     sda: sda1
    sd 1:0:0:0: [sda] Assuming drive cache: write through
    sd 1:0:0:0: [sda] Attached SCSI disk
    eth0: no IPv6 routers present
    VFS: Mounted root (jffs2 filesystem) on device 31:6.
    devtmpfs: mounted
    Freeing unused kernel memory: 128k freed
    EXT4-fs (sda1): warning: mounting fs with errors, running e2fsck is recommended
    EXT4-fs (sda1): mounted filesystem with ordered data mode
    stmcore-display: using HDMI hotplug
    stmcore-display: STi7105 display: probed
    device probe found 2 display pipelines
    requesting frm: 'component.fw', c11e88c4/876bb610
     stm-awg: firmware: requesting component.fw
    frm 'component.fw' successfully loaded
    requesting frm: 'fdvo0.fw', c11e88c4/876bbd90
     stm-awg: firmware: requesting fdvo0.fw
    frm 'fdvo0.fw' successfully loaded
    [CEC] init - starting
    [CEC] The above error is a wanted behaviour as this was a ping!
    Fulan front panel driver
    VfdType = 2
    CpuType = 2
    DisplayInfo = 1
    scankeyNum = 8
    swMajorVersion = 1
    swSubVersion = 10
    stby key 0 = 44bbb24d
    stby key 1 = a25d7887
    stby key 2 = 00000000
    stby key 3 = 00d90000
    stby key 4 = 00000000
    blue key 0 = 44bbb847
    blue key 1 = a25d52ad
    blue key 2 = 000a0003
    blue key 3 = 00000000
    blue key 4 = 00000000
    input: fulan front panel buttons as /devices/virtual/input/input0
    aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
    aotom_rtc_probe 87669800
    aotom_rtc_probe 2
    stmfb: fb0 parameters = "1280x720-32@50:15m:pal:yuv:yuv"
    stmfb: Starting HDMI Output hdmi = 87700000
    stmfb: fb1 parameters = "<NULL>"
    Init of MME log wrapper
    stm_v4l2_register_driver: driver 'stmvout' registered
    stm_v4l2_register_driver: driver 'stmvbi' registered
    snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
    pseudocard: 1 pseudo soundcard(s) found
    pti: module license 'NO' taints kernel.
    Disabling lock debugging due to kernel taint
    pti loaded (videoMem = 4096, waitMS = 20, enableStatistic = 0)
    no swts ->routing streams from dvr0 direct to the player
    DVB: registering new adapter (STM Streamer)
    0: DeviceContext 869c8088, DvbDemux 869c84c4, DmxDevice 869c86ac
    CaInit()
    Initializing CI Controller
    ptiInit context = 869c8088, demux = 869c84c4
    [TSM] init stream routing...
    Bypass ci
    >>Init st7105 DVBT-USB
    TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            Load real TC Code
    TC_Data = fe238000, TC_Code = fe23c000
    Readback TC ... successfull
    using videoMem = 770048 (packets = 4096)
    pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
    DMA(0) base = 49380000, top = 4943c000, buffer = 49380000, size 770048
    freeBuffer(): free = 1
    pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
    DMA(1) base = 4943c000, top = 494f8000, buffer = 4943c000, size 770048
    freeBuffer(): free = 2
    pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
    DMA(2) base = 494f8000, top = 495b4000, buffer = 494f8000, size 770048
    freeBuffer(): free = 3
    pI2c = 0x87e69218
    pti_task: using 3 dma channel
    pucActualID = 2
    [demod_d6158_Identify] Got Demode 88472!
    DEMO_BANK_T2
    [dvb_d6158_attach]418,open result=0
    spark_dvb_attach_T2: d6158 attached
    mxl301_attach: Attaching sharp6465 (mxl301) tuner
    spark_dvb_attach_T2:mxl301 attached
    DVB: registering adapter 0 frontend 3 (Tuner3-T/T2(T/T2/C))...
    pI2c = 0x87e69418
    spark_dvb_attach_s: d3501 attached
    ix7306_write ucIOBuffer 4 Err = 0
    ix7306_write ucIOBuffer 1 Err = 0
    ix7306_write ucIOBuffer Err 2 = 0
    ix7306_read Err = 0 ucData = 0x18
    ========tuner_sharp7306_identify =====
    tuner_Sharp7306 is Identified
    ix7306_attach: Attaching Sharp BS2S7HZ7306A IX7306 8PSK/QPSK tuner
    spark_dvb_attach_s: IX7306 attached
    DVB: registering adapter 0 frontend 1 (Tuner1-Sat)...
    pI2c = 0x87e69018
    spark_dvb_attach_s: d3501 attached
    ix7306_write ucIOBuffer 4 Err = 0
    ix7306_write ucIOBuffer 1 Err = 0
    ix7306_write ucIOBuffer Err 2 = 0
    ix7306_read Err = 0 ucData = 0x18
    ========tuner_sharp7306_identify =====
    tuner_Sharp7306 is Identified
    ix7306_attach: Attaching Sharp BS2S7HZ7306A IX7306 8PSK/QPSK tuner
    spark_dvb_attach_s: IX7306 attached
    DVB: registering adapter 0 frontend 0 (Tuner2-Sat)...
    Free session: 0
    Using session 0
    Descrambler Handler = 40000
    install_e2_procs(): entry already in use 'progress'
    install_e2_procs(): entry already in use 'stb/fp/was_timer_wakeup'
    1: DeviceContext 869c8748, DvbDemux 869c8b84, DmxDevice 869c8d6c
    CaInit()
    ptiInit context = 869c8748, demux = 869c8b84
    Free session: 1
    Using session 1
    Descrambler Handler = 41000
    2: DeviceContext 869c8e08, DvbDemux 869c9244, DmxDevice 869c942c
    CaInit()
    ptiInit context = 869c8e08, demux = 869c9244
    Free session: 2
    Using session 2
    Descrambler Handler = 42000
    3: DeviceContext 869c94c8, DvbDemux 869c9904, DmxDevice 869c9aec
    ptiInit context = 869c94c8, demux = 869c9904
    Descrambler Handler = -2
    stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered
    OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0
    AllocatorLoadModule : Allocator device loaded
    Switching Preprocessor clock to full speed.
    OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0
    H264ppLoadModule : H264pp device loaded
    (bpamem_init): BPAMem driver register result = 0
    [simu_button] initializing ...
    [simu_button] allocating and registering button device
    input: TDT RC event driver as /devices/virtual/input/input1
    Registering device 'sc', major '169'
    Version of smartcard driver: [1.0.1]
    ramzswap: disk size not provided. You can use disksize_kb module param to specify size.
    Using default: (25% of RAM).
    ramzswap: disk size set to 29004 kB
    ramzswap: Initialization done!
    Adding 29000k swap on /dev/ramzswap0.  Priority:-1 extents:1 across:29000k SS
    LinuxDvb:DvbPlaybackCreate: Playback 861c6060
    input: remote control as /devices/virtual/input/input2
    VFD/AOTOM: unknown IOCTL 0x1015
    stmhdmiio_get_cec_address - 87700000
    proc_tsmux_input0_write 1 A
    proc_tsmux_input1_write 1 B
    DVB: adapter 0 frontend 3 frequency limits undefined - fix the driver
    failed to get output window -22
    failed to set output window -22
    failed to get output window -22
    failed to set output window -22
    failed to get output window -22
    failed to set output window -22
    failed to get output window -22
    failed to set output window -22
    proc_denc_0_wss_write 4 - auto
    proc_hdmi_edid_handling_read
    stmhdmiio_get_edid_handling - 87700000
    proc_hdmi_edid_handling_read - 1
    proc_hdmi_edid_handling_read
    stmhdmiio_get_edid_handling - 87700000
    proc_hdmi_edid_handling_read - 1
    proc_hdmi_edid_handling_read
    stmhdmiio_get_edid_handling - 87700000
    proc_hdmi_edid_handling_read - 1
    proc_hdmi_edid_handling_write 8 - [HDMI] EDID handling arg: 00000001
    [HDMI] EDID handling: none strict
    stmhdmiio_set_edid_handling - 87700000
    proc_hdmi_audio_source_read
    stmhdmiio_get_audio_source - 87700000
    proc_hdmi_audio_source_read - 0
    proc_hdmi_audio_source_read
    stmhdmiio_get_audio_source - 87700000
    proc_hdmi_audio_source_read - 0
    proc_hdmi_audio_source_read
    stmhdmiio_get_audio_source - 87700000
    proc_hdmi_audio_source_read - 0
    proc_hdmi_audio_source_write 3 - pcm
    stmhdmiio_set_audio_source - 87700000
    Found mode to set 720p50 at 21
    Found mode to set 720p50 at 21
    Found mode to set 720p50 at 21
    power_standbyled_write(2, ononERROR:LinuxDvb:DvbDisplayDelete: Failed to close audio surface
    ERROR:LinuxDvb:DvbDisplayDelete: Failed to close audio surface
    aotom_write_rtc_offset 4 - aotom_write_rtc_offset -> 3600
     offset: 3600
    aotom_write_rtc 13 - aotom_write_rtc -> 1455368874.16
    pti_hal_set_source(): 0, 33
    reset_tsm: 1 numRunningFeeds: 0 => calling stm_tsm_init(1)
    [TSM] reinit stream routing...
    Bypass ci
    reinit
    >>Init st7105 DVBT-USB
    TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            TsinMode = Parallel *st-merger*
            start dmx 869c84c4, sh 10000, pid 20, t 1, pt 0
    getBuffer(): free = 3
    pti_buffer_get(770048) => 877d64d0
    stpti_start_feed: pid = 20, num_pids = 1
    start dmx 869c84c4, sh 10000, pid 5106, t 0, pt 0
    (da 0, 1)
    stpti_start_feed: pid = 5106, num_pids = 2
    Find spdif_bypass control at 8762a680
    start dmx 869c84c4, sh 10000, pid 5101, t 0, pt 1
    (da 0, 2)
    stpti_start_feed: pid = 5101, num_pids = 3
    start dmx 869c84c4, sh 10000, pid 5104, t 0, pt 2
    stpti_start_feed: pid = 5104, num_pids = 4
    start dmx 869c84c4, sh 10000, pid 5104, t 0, pt 20
    (da 0, 3)start dmx 869c84c4, sh 10000, pid 5104, t 0, pt 20
    (da 0, 3)start dmx 869c84c4, sh 10000, pid 0, t 1, pt 825636917
    stpti_start_feed: pid = 0, num_pids = 5
    ksound: Set parameters for hw:0,2 to 2 x 48000hz with period 1536 (of 4608)
    ksound: Set parameters for hw:0,1 to 2 x 48000hz with period 1536 (of 4608)
    ksound: Set parameters for hw:0,0 to 2 x 48000hz with period 1536 (of 4608)
    sound/stm/conv_i2sspdif.c:204: WARNING! Failed to set channel status registers for converter snd_conv_i2sspdif.0! (tried 6 times)
    sound/stm/conv_i2sspdif.c:290: WARNING! Can't set channel status registers!
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 0, t 1, pt 825636917
    stpti_start_feed: pid = 0, num_pids = 6
    aotom_write_rtc 10 - aotom_write_rtc -> 1455368876
    start dmx 869c84c4, sh 10000, pid 0, t 1, pt 825636917
    stpti_start_feed: pid = 0, num_pids = 5
    start dmx 869c84c4, sh 10000, pid 5100, t 1, pt 0
    stpti_start_feed: pid = 5100, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 0, t 1, pt 825636917
    stpti_start_feed: pid = 0, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 0, t 1, pt 825636917
    stpti_start_feed: pid = 0, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 5100, t 1, pt 0
    stpti_start_feed: pid = 5100, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 17, t 1, pt 16
    stpti_start_feed: pid = 17, num_pids = 7
    start dmx 869c84c4, sh 10000, pid 5100, t 1, pt 0
    stpti_start_feed: pid = 5100, num_pids = 7
    start dmx 869c84c4, sh 10000, pid 1170, t 1, pt 172
    stpti_start_feed: pid = 1170, num_pids = 8
    start dmx 869c84c4, sh 10000, pid 1170, t 1, pt 172
    stpti_start_feed: pid = 1170, num_pids = 8
    start dmx 869c84c4, sh 10000, pid 5100, t 1, pt 0
    stpti_start_feed: pid = 5100, num_pids = 8
    start dmx 869c84c4, sh 10000, pid 5100, t 1, pt 0
    stpti_start_feed: pid = 5100, num_pids = 8
    start dmx 869c84c4, sh 10000, pid 5110, t 1, pt -1
    stpti_start_feed: pid = 5110, num_pids = 9
    start dmx 869c84c4, sh 10000, pid 5120, t 1, pt -1
    stpti_start_feed: pid = 5120, num_pids = 9
    start dmx 869c84c4, sh 10000, pid 5130, t 1, pt -1
    stpti_start_feed: pid = 5130, num_pids = 9
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 9
    start dmx 869c84c4, sh 10000, pid 3842, t 1, pt -1
    stpti_start_feed: pid = 3842, num_pids = 9
    start dmx 869c84c4, sh 10000, pid 3003, t 1, pt 1953394531
    stpti_start_feed: pid = 3003, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 5000, t 1, pt 1634038367
    stpti_start_feed: pid = 5000, num_pids = 11
    start dmx 869c84c4, sh 10000, pid 5000, t 1, pt 1634038367
    stpti_start_feed: pid = 5000, num_pids = 11
    start dmx 869c84c4, sh 10000, pid 57, t 1, pt 29
    stpti_start_feed: pid = 57, num_pids = 12
    start dmx 869c84c4, sh 10000, pid 5172, t 1, pt 172
    stpti_start_feed: pid = 5172, num_pids = 12
    start dmx 869c84c4, sh 10000, pid 5172, t 1, pt 172
    stpti_start_feed: pid = 5172, num_pids = 12
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 5000, t 1, pt 1634038367
    stpti_start_feed: pid = 5000, num_pids = 10
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 6
    start dmx 869c84c4, sh 10000, pid 18, t 1, pt 10652
    stpti_start_feed: pid = 18, num_pids = 6
    root@sparktriplex:~#
    Geändert von SML (14.02.2016 um 22:39 Uhr)
    MfG
    SML

    DM920 | GI-Xpeed LX3 | GM Triplex T2
    MS: Spaun SMS 9807 für Astra / Hotbird

    Kathrein CAS90 45E-45W mit GT-SAT Unicable-LNB GT-S1dCSS24 16UB

    •   Alt Advertising

       

  2. #2
    rantanplan
    Gast
    Ist nicht gänzlich unbekannt.
    Du liest ja auch im HDMU mit, daher ist dir das ja bzgl der pti.ko bestimmt auch bekannt.
    Da kann man etwas spielen. Aber so ganz scheint es nicht zu beheben sein.
    Manchmal hilft das Festlegen vom Startkanal.
    Wenn man den Tuner wieder sichtbar haben will, dann hilft auch zumeist die Wiedergabe von Videofiles.
    Mitlerweile läuft aber doch das 5.1 recht gut

  3. Thanks SML bedankten sich
  4. #3
    Senior Mitglied
    Registriert seit
    03.03.2015
    Ort
    Bayern
    Beiträge
    141
    Thanks (gegeben)
    65
    Thanks (bekommen)
    15
    Themenstarter
    Total Downloaded
    21,15 MB
    Total Downloaded
    21,15 MB
    ReceiverDanke
    Box 1:
    DM920 1x DVB-S2X FBC, 1x Dual DVB-S2
     
     
    Box 2:
    Xpeed LX3 4x DVB-S2
     
     
    Box 3:
    GM Triplex T2
     
     
    Zitat Zitat von rantanplan Beitrag anzeigen
    Mitlerweile läuft aber doch das 5.1 recht gut
    Das ist schon richtig, mir fiel es halt jetzt beim testen vom 4.2 auf, die pti.ko habe ich bisher noch nie gewechselt.
    MfG
    SML

    DM920 | GI-Xpeed LX3 | GM Triplex T2
    MS: Spaun SMS 9807 für Astra / Hotbird

    Kathrein CAS90 45E-45W mit GT-SAT Unicable-LNB GT-S1dCSS24 16UB

  5. #4
    rantanplan
    Gast
    ist immer einen Test wert...aber 4.2 wird eh bald eingestellt.
    Alles auf 5.2 heißt es ja.

  6. #5
    Senior Mitglied
    Registriert seit
    05.04.2013
    Beiträge
    1.113
    Thanks (gegeben)
    346
    Thanks (bekommen)
    267
    Total Downloaded
    320,66 MB
    Total Downloaded
    320,66 MB
    ReceiverDanke
    Zitat Zitat von rantanplan Beitrag anzeigen
    ist immer einen Test wert...aber 4.2 wird eh bald eingestellt.
    Alles auf 5.2 heißt es ja.

    ..tja.auf zu neuen "ufern".....
    ............................
    Gruss Joker7
    Ein Tag ohne lächeln ist ein verlorener Tag
    ( Charlie Chaplin )


  7. #6
    satpete
    Gast
    beim 5.1 und 5.2 habe ich ebenfalls nach dem Booten kein Bild, schwarzer Bildschirm und abgehackter Ton,
    unabhängig davon, ob Startkanal aktiviert ist, bei Sat+Kabel gleicher Fehler;
    ich muss erst auf einen anderen Kanal umschalten, dann sind Bild+Ton da

  8. #7
    Anfänger
    Registriert seit
    21.07.2014
    Beiträge
    23
    Thanks (gegeben)
    5
    Thanks (bekommen)
    1
    Total Downloaded
    0
    Total Downloaded
    0
    ReceiverDanke
    Hier genau das gleiche Problem: Mit der letzten Version 4.2 kein Bild aber sauberer Ton, bei 5.3 kein Bild und stotternder Ton nach jedem Neustart bis zum Umschalten auf einen anderen Kanal auf meiner GM Triplex. Etwas schade, dass es hierfür keine Lösung gibt. Scheinbar hilft nur ein downgrade auf 4.1...

  9. #8
    Mitglied
    Registriert seit
    23.11.2014
    Beiträge
    70
    Thanks (gegeben)
    8
    Thanks (bekommen)
    4
    Total Downloaded
    291,42 MB
    Total Downloaded
    291,42 MB
    ReceiverDanke
    Ich hab einen SD_SENDER als StartKanal eingestellt. Vielleicht wird dieses Problem ja nochmal behoben. Ansonsten bin ich mit den ATV-IMAGE zufrieden (vorher HDMU-IMAGE).

    früher gab es AbschnittsBevollmächtigte, heute gibt es stumi's


Stichworte

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
Alle Zeitangaben in WEZ +1. Es ist jetzt 05:33 Uhr.
Powered by vBulletin® Version 4.2.5 (Deutsch)
Copyright ©2024 Adduco Digital e.K. und vBulletin Solutions, Inc. Alle Rechte vorbehalten.
Resources saved on this page: MySQL 5,88%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
vBulletin Skin By: PurevB.com